ISO 9001:2015 Stockist & Fabricator | Sharjah HQ Stockyard | Abu Dhabi Branch
Leema Engineering Works

Pig Launcher and Receiver Fabrication UAE: Pig Traps Built to Your Design Code

Leema Engineering Works offers pig launcher and receiver fabrication UAE pipeline operators and EPC contractors use for new lines, station upgrades and replacement traps. We build each pig trap to your datasheet in our Sharjah workshop [confirm], with quick-opening closures, major and minor barrels, nozzles and supports, and we agree the design code with you before any steel is cut. Every pig launcher and receiver we build is welded by qualified welders, hydrotested and shipped with a full document pack. Send your design inputs and our engineers return a drawing, a price and a lead time.

What Do Pig Launchers and Receivers Do?

A pig launcher puts a pig into a live pipeline, and a pig receiver takes it out at the far end, without shutting the line down. Together they are called a pig trap. The launcher holds the pig in an oversized major barrel; flow from a kicker line pushes it through a reducer and the minor barrel into the main line. At the receiving end the pig arrives in the receiver barrel, is isolated, depressurised and removed through the closure. Pig launchers and receivers are pressure equipment, not simple fittings, so the fabricator matters. A workshop with proven pig launcher and receiver fabrication UAE experience builds and tests the trap close to site.

At a glance, our pig launcher and receiver fabrication covers:

  • Traps: launchers, receivers and bi-directional traps, horizontal or vertical.
  • Closures: quick-opening closure with pressure warning interlock, or a bolted blind on request.
  • Barrels: major barrel, eccentric or concentric reducer, launcher barrel or receiver barrel to line size.
  • Nozzles: kicker line, balance, vent, drain, pressure gauge and relief connections, plus pig signaller bosses.
  • Packages: single traps or a pigging skid with valves, piping and a pig handling tray.

Design Inputs for Your Pig Trap

Good pig launcher and receiver fabrication UAE clients can rely on starts with complete data. These inputs let us size the barrels of your pig launchers and receivers and confirm the design before we order material.

  • Pipeline size, wall thickness, material grade and planned pipeline pigging frequency.
  • Design pressure, design temperature and corrosion allowance.
  • Fluid and service, including sour service or low temperature requirements.
  • Longest pig you plan to run. Inline inspection tools are much longer than cleaning pigs and usually set the major barrel length.
  • Governing code and operator specification, plus closure type, orientation and space limits on site.

If you only have a P&ID and a line list, send those. We fill the gaps with questions, not guesses. Complete inputs keep our pig launcher fabrication schedule on track. Tell us early if the barrel needs ASME Section VIII design, since it changes the calculation.

Pig Launcher and Receiver Fabrication UAE: Sizes, Classes and Materials

Pig launchers and receivers are made to order, so this is our working envelope, not a stock list. We confirm every limit on the drawing before fabrication starts. As a workshop focused on pig launcher and receiver fabrication UAE wide, we match barrel material to the line pipe so welds and corrosion behaviour stay consistent.

  • Pipeline sizes: from [confirm, e.g. NPS 4] to [confirm, e.g. NPS 36], with the major barrel usually one or two sizes larger than the line.
  • Pressure classes: ASME Class 150 to 1500 [confirm], with wall thickness calculated for design pressure and corrosion allowance.
  • Carbon steel: API 5L and ASTM A106 pipe, ASTM A234 WPB fittings and ASTM A105 nozzles and flanges.
  • Low temperature carbon steel: ASTM A333 Gr 6 pipe and A350 LF2 forgings.
  • Stainless and duplex: on request [confirm].
  • Closures: from established closure makers [confirm brands], or supplied by you.

For sour service, all pressure parts meet NACE MR0175 hardness limits, and we record hardness after welding and heat treatment.

Closures, Barrels and Nozzles: How We Fabricate a Pig Trap

The closure is the part operators open most often, so it gets the most attention. A quick-opening closure must not open while there is pressure in the barrel; we fit a pressure warning device or interlock so the door cannot be released until the trap is vented. This is where specialist pig launcher and receiver fabrication UAE operators trust differs from general welding work.

How we fabricate pig launchers and receivers, step by step:

  • Barrels: The major barrel is sized to hold the longest pig, with room for a second pig where needed. The reducer joins it to the launcher barrel or receiver barrel, which matches the pipeline bore.
  • Nozzles: Kicker line, balance line, vent, drain, gauge and relief nozzles are set out to your P&ID. A pig signaller boss sits on the minor barrel to confirm the pig has left or arrived.
  • Welding: All pressure welds use approved WPS and PQR procedures and ASME Section IX qualified welders.
  • Heat treatment: Post weld heat treatment is applied where the code, material or wall thickness calls for it.
  • Supports and handling: Saddles, lifting lugs and a pig handling tray are fabricated with the trap, so pig launchers and receivers arrive ready to install.

Where your line needs a barred tee next to the trap, we fabricate it in the same workshop and test it with the package.

Where Pig Launchers and Receivers Are Used

Any line that is cleaned or inspected by pipeline pigging needs a pig trap at each end. Typical sites include export and transfer lines, gas gathering networks, water injection lines and offshore risers and tie-ins. Pig launchers and receivers in the UAE serve both onshore and offshore pipeline pigging, and receivers usually take the heavier wear from debris. Plan pig handling space beside every trap so crews can load and remove pigs safely. On our oil and gas industry page you can see how traps fit into a full pipeline package of pipe, fittings and flanges.

Which Design Code Applies: ASME B31.4, B31.8 or Section VIII?

Settle this first; it changes wall thickness, testing and paperwork.

  • Pipeline codes: Many operators treat pig launchers and receivers as part of the pipeline. Liquid lines then follow ASME B31.4 and gas lines follow ASME B31.8, with the same design factor as the line. Every pig launcher and receiver supplier should confirm the code in writing before quoting.
  • Pressure vessel code: Other operators classify the major barrel as a pressure vessel and require ASME Section VIII, Division 1. That usually means thicker barrels, a vessel calculation and vessel-style inspection.
  • Operator specification: The client specification decides between the two and often adds rules for closures, nozzles and testing. Shell DEP and national oil company specifications are common in the GCC.

Our advice is simple: name the code on your enquiry. If you are unsure, send the line data and specification, and our pig launcher and receiver fabrication UAE engineers will give a written view before you order. We will not start a drawing on an assumed code [confirm which codes Leema designs to].

Testing, NDT and Documents

Testing is where pig launcher and receiver fabrication UAE buyers can audit proves its quality. Every trap leaves the workshop with proof that it was built and tested as drawn.

  • Visual and dimensional checks against the approved drawing, including nozzle orientation and closure alignment.
  • Radiographic or ultrasonic testing on butt welds, and magnetic particle or dye penetrant testing on nozzle and attachment welds [confirm methods].
  • Hydrotest of the complete trap, including the closure, at the code test pressure.
  • Hardness testing for sour service, and PMI on alloy parts.
  • Function check of the pig signaller and closure interlock before dispatch.
  • Document pack: drawing, design calculation, weld map, WPS and PQR, welder qualifications, NDT reports, heat treatment charts, hydrotest record and EN 10204 3.1 certificates. Third-party inspectors are welcome at any hold point during pig launcher fabrication.

Recent Jobs

[Confirm and replace with authorised references.] Job 1: [size and class] launcher and receiver pair in [material] for [end user or EPC], [year], to [code]. Job 2: [quantity] pig traps on a pigging skid for [project], with hydrotest witnessed by [inspection agency]. Choosing local pig launcher and receiver fabrication UAE inspectors can witness in person also supports In-Country Value goals and shortens delivery.

Lead Time and Delivery

For pig launcher and receiver fabrication UAE projects, typical lead time is [confirm] weeks from drawing approval, depending on size, code, closure delivery and testing. Finished traps are delivered across the UAE and shipped to GCC projects with export documents.

Related Pages

Other services from our pig launcher and receiver fabrication UAE workshop: Barred Tee Fabrication, our Fabrication and Engineering Services overview, Oil and Gas, and Flanges for trap connections.

Pig Launcher and Receiver Fabrication UAE FAQs

What is the difference between a pig launcher and a pig receiver?

A launcher sends the pig into the line and a receiver catches it. Receivers often have a longer major barrel to hold debris pushed ahead of the pig.

How long should the major barrel be?

Long enough for the longest pig plus space to close the door. Inline inspection tools usually set this length.

Do you supply the closure and valves?

With our pig launchers and receivers we supply the closure fitted and tested. Valves for a pigging skid can be supplied by us or by you [confirm].

Can you modify or repair an existing pig trap?

Often yes, after we check its drawings, certificates and wall thickness. Repairs are recorded in a new document pack.

Do pig traps need inline inspection allowances?

Yes, if you plan to run inline inspection tools. The major barrel, bends and valves must suit their length and stiffness.

Can pig launcher and receiver fabrication UAE projects include the pigging skid?

Yes. We build the skid frame, piping and supports around the traps and test them as one unit.

Why use local pig launcher and receiver fabrication instead of importing?

Shorter lead time, faster drawing changes and witness testing without travel.

Who approves the design?

Our engineer prepares the drawing and calculation to ASME B31.4, B31.8 or ASME Section VIII; your engineer or the operator approves it before fabrication starts.

Send Your Pig Trap Design Inputs

Upload your launcher barrel and receiver datasheet, P&ID or line list and our pig launcher fabrication team replies with a drawing, price and lead time within [confirm] working days. Call +971 6 533 8167, WhatsApp [confirm number] or email sales@leemaeng.com. You can also use the Request a Quote page.

Request a Quote Call +971 6 533 8167