Spiral Wound Gasket Supplier UAE: Gaskets and ASTM A193 B7 Stud Bolts
Leema Engineering Works is a spiral wound gasket supplier UAE flange owners can use to complete a joint, with ASME B16.20 spiral wound and ring joint gaskets and ASTM A193 B7 stud bolts with A194 2H nuts [confirm range]. Material certificates travel with every shipment from our Sharjah and Abu Dhabi stores, and brand options and availability are confirmed when you enquire. Read on for gasket types, bolting grades, how to match both to a flange class, and what to verify before you order. Send your flange list with size, class, facing and service, and our team replies with price and lead time.
Spiral Wound Gasket Supplier UAE at a Glance
A flanged joint is only as tight as its gasket and bolting, and a mismatch shows up as a weep at start-up or a leak after the first thermal cycle. ASME B16.20 covers metallic gaskets such as spiral wound and ring joint types, and ASME B16.21 covers flat non-metallic gaskets. As a spiral wound gasket supplier UAE specifiers contact before shutdowns, we check every set against the flange datasheet. The range is listed below at a glance, and every quotation names the gasket type, materials, flange class and bolt grade so the set matches your line class.
- Gaskets: Spiral wound, ring joint, flat sheet [confirm range]
- Standards: ASME B16.20 (metallic); ASME B16.21 (non-metallic)
- Winding strip: 316L, 304, 321 [confirm stocked materials]
- Fillers: Flexible graphite, PTFE
- Ring joint rings: Soft iron, low carbon steel, F5, 316 [confirm]
- Stud bolts: ASTM A193 B7, B7M, B8M
- Nuts: A194 2H, 2HM, 8M
- Coatings: Plain, PTFE-coated, galvanised [confirm]
- Certificates: EN 10204 3.1 for bolting and gasket materials
- Lead time: Confirmed in the quotation
Gasket and Stud Bolt Types We Supply
Three gasket families and one bolting family cover most enquiries. Choose the type from the flange facing, class and fluid first, then the materials [confirm stocked types and brands]. Spare sets for a shutdown can be bundled by joint number.
- Spiral wound gaskets: A V-shaped metal strip wound together with soft filler seals under load and recovers when pressure and temperature change. Graphite-filled spiral wound gaskets handle high temperature, PTFE-filled types suit chemicals, and a 316L spiral wound gasket is the usual winding for general process lines. Inner and outer rings control compression and centre the gasket in the bolt circle.
- Ring joint type: RTJ gaskets are solid metal rings that sit in a machined groove and seal at very high pressure. R and RX rings fit ASME B16.5 grooves, and BX rings fit API 6BX flanges. The ring must be softer than the flange groove, so soft iron, low carbon steel, F5 and 316 rings are chosen by service. They are single use.
- Flat sheet gaskets: Compressed fibre, flexible graphite and PTFE sheet gaskets to ASME B16.21 suit low-pressure joints and flat-face equipment connections [confirm range].
- Stud bolts and nuts: ASTM A193 B7 stud bolts with A194 2H nuts are the standard set for carbon steel flanges at pressure and temperature, and stud bolts B7 and 2H are supplied as full-thread studs with two heavy hex nuts each. B7M with 2HM has lower hardness for hydrogen sulphide environments, and B8M with 8M nuts suits stainless steel joints. PTFE-coated stud bolts resist corrosion outdoors and cut friction during tightening.
Sizes, Classes and Matching to the Flange
ASME B16.20 gaskets are sized to ASME B16.5 flanges from NPS 1/2 to 24 in classes 150 to 2500, and to B16.47 Series A and B for larger sizes, so state the standard on our flanges page when you match a set. Spiral wound gaskets are ordered by nominal size, class, winding, filler and ring configuration. Inner rings are required with PTFE filler and recommended on higher classes, vacuum or cyclic service. Any spiral wound gasket supplier UAE flange owners rely on should ask for the flange standard and facing before quoting. Stud bolts B7 and 2H are ordered by diameter, thread, length and quantity per joint, and the hole count and bolt size come from the flange table. Coarse UNC threads apply up to one inch and 8UN threads above, and length must cover the flange thickness, the gasket, two nuts and the thread projection. For non-standard flanges, see our custom flanges page, because the gasket then needs a drawing. Our stocked range runs [confirm] to [confirm] NPS [confirm classes].
Where Gaskets and Stud Bolts Are Used
Every bolted joint needs both. Oil and gas: spiral wound gaskets on Class 300 and above, and RTJ gaskets on high-pressure hydrocarbon lines, as detailed on our oil and gas page. A spiral wound gasket supplier UAE refineries use must also keep stock of the matching bolting, because a joint cannot be closed with half a set. Power generation: graphite-filled windings and B7 bolting on steam and feedwater joints, covered on our power generation page. Shipbuilding and marine yards: cooling and ballast joints that need coated or stainless bolting, see our marine page. Process and utility plants: chemical lines where winding and filler must resist the fluid. In each case the joint specification, not the nearest stock item, sets the gasket and the bolt grade, so confirm the joint list with your piping engineer before ordering.
Which Gasket and Bolting Do You Need for Your Flange?
Start with the flange. If the flange has a ring groove, you need a ring joint gasket; if the face is raised, a spiral wound gasket is usually right at Class 300 and above, and flat sheet is acceptable only at lower pressure. Next, match the filler to the fluid and temperature: graphite-filled spiral wound gaskets for heat and steam, PTFE-filled types for aggressive chemicals. Then match the winding to the corrosion risk, with 316L for most services. Choose the bolting from the flange material and environment, using stud bolts B7 and 2H for carbon steel, B7M with 2HM where hardness limits apply, and B8M with 8M for stainless.
Buy gasket and stud bolt sets together so grades, classes and certificates agree, and do not reuse gaskets or rings. Tighten in a cross pattern in several passes, following ASME PCC-1 bolt tightening guidance, because uneven loading is a common cause of leaks. Send the flange list and we will check each set against it before you order.
Certificates, Testing and Marking
Bolting and gasket materials ship with EN 10204 3.1 certificates, and we can request 3.2 where an inspector must witness. Stud bolts carry a grade marking that ties them to the certificate, and hardness results are on the report. A spiral wound gasket supplier UAE operators approve will hand over these records with each order. ASME B16.20 gaskets are marked and colour-coded for winding and filler, and ring joint gaskets are stamped with the ring number and material. PMI can be requested to verify the winding strip or ring alloy. Together these records let you trace every set to its lot. Country of manufacture is shown on the paperwork, and our Quality and Approvals page explains how we inspect.
Spiral Wound Gasket Supplier UAE: Stock and Lead Time
Common gaskets and stud bolts sit at the Sharjah and Abu Dhabi warehouses [confirm which items each site holds]. We pack gasket and stud bolt sets per joint on request. Items outside stock are ordered from the manufacturer, and the quotation states the resulting lead time. Teams planning a shutdown should ask early, because bolting sets are cheap but missing ones stop a restart. Export orders go out with the paperwork and test records that customs and inspectors expect.
Spiral Wound Gasket Supplier UAE FAQs
What is the inner ring on a spiral wound gasket for? +
It stops the winding from buckling inward, controls compression and keeps the filler away from the fluid. It is required with PTFE filler and recommended on higher classes.
What do the colours on a spiral wound gasket mean? +
The colour bands identify the winding material and the filler under ASME B16.20. Check them against your specification before fitting, and keep the gasket in its packaging until the joint is ready to close.
Can an RTJ ring be reused? +
No. The ring deforms to the groove when tightened, so a used ring may not seal. Replace it at every joint opening, even if the old ring looks undamaged.
Why do stud bolts need two nuts? +
One nut sits at each end of the stud. Stud bolts are threaded along the full length, so a nut at each end clamps the flanges evenly. Follow ASME PCC-1 bolt tightening for the pattern and number of passes.
What is the difference between B7 and B7M? +
B7M is tempered to lower hardness for environments with hardness limits. B7 is stronger and suits general high-pressure and high-temperature joints.
What should I check before choosing a spiral wound gasket supplier UAE buyers can verify? +
Confirm the standard, winding, filler and ring configuration against your datasheet, check that bolting is matched to the flange material, and ask for the material certificate and the bolt grade marking.
Request a Gasket and Stud Bolt Quote
Upload your BOQ or MTO with flange size, class, facing, service and quantity. Our Sharjah and Abu Dhabi teams reply with price, brand options and lead time within [response time]. Call +971 6 533 8167 or email sales@leemaeng.com, or message us on WhatsApp [number]. Mention the line class or specification and we will check each set against it.
Reviewed by [Engineer name], last reviewed 16 October 2026.