Pipe Schedule and Weight Chart
This pipe schedule chart gives the outside diameter, wall thickness and weight in kg/m of steel pipe from NPS 1/8 to NPS 48, for carbon steel to ASME B36.10M and stainless steel to ASME B36.19M. Use it to check a drawing, convert a schedule to millimetres, or estimate the weight of a pipe order before you request a quote. Every figure comes from the standards, and weights are calculated with the standard formula shown below, so you can check any number yourself.
Reviewed by [Engineer name], [Role], Leema Engineering Works. Last reviewed [date].
Pipe Schedule Chart at a Glance
Before the tables, here is what this reference covers [build as an HTML table on the live page].
- Standards: ASME B36.10M for welded and seamless wrought steel pipe (carbon and alloy), and ASME B36.19M for stainless steel pipe.
- Sizes: NPS 1/8 to NPS 24 in schedules, plus NPS 30 to 48 in STD and XS walls.
- Schedules: SCH 40, 80 and 160 and XXS for carbon steel; 5S, 10S, 40S and 80S for stainless steel.
- Units: OD and wall thickness in millimetres, weight in kilograms per metre (kg/m) of plain-end pipe.
- Weight formula: (OD minus WT) x WT x 0.02466 gives kg/m for carbon steel, the basis of the pipe weight chart.
These are standard dimensions; the sizes Leema actually holds in stock are shown on our Pipes page.
How to Read the Pipe Schedule Chart
Pipe size is described by two numbers: the nominal pipe size (NPS) and the schedule. Reading a pipe schedule chart correctly starts with three rules.
- NPS is a name, not a measurement: from NPS 1/8 to NPS 12, the outside diameter is larger than the NPS number suggests (NPS 2 has an OD of 60.3 mm, not 50.8 mm). From NPS 14 upward, the OD in inches equals the NPS.
- The OD stays fixed for each NPS: every schedule of NPS 4 has the same 114.3 mm outside diameter, so fittings and flanges line up. Only the wall thickness changes, which changes the bore, or inside diameter.
- The schedule sets the wall: a higher schedule number means a thicker wall, a smaller bore, more weight and a higher pressure rating for the same material.
To find a size, go to the NPS row, read across to the schedule, and take the wall thickness and weight from that cell. To find the inside diameter from this pipe weight chart, subtract twice the wall thickness from the OD: NPS 4 SCH 40 has a bore of 114.3 minus 12.04, or 102.26 mm. Many buyers in the UAE and GCC also quote the metric DN size; DN 100 is the same pipe as NPS 4.
Carbon Steel Pipe Schedule Chart (ASME B36.10M)
This carbon steel pipe schedule chart covers the sizes and walls most used in oil and gas, process and utility piping [build as an HTML table: NPS, OD, then wall and weight per schedule; check every figure against the current edition of ASME B36.10M before publishing].
| NPS | OD (mm) | SCH 40 (Wall / Wt) | SCH 80 (Wall / Wt) | SCH 160 (Wall / Wt) | XXS / STD / XS (Wall / Wt) |
|---|---|---|---|---|---|
| NPS 1/8 | 10.3 mm | 1.73 mm, 0.37 kg/m | 2.41 mm, 0.47 kg/m | - | - |
| NPS 1/4 | 13.7 mm | 2.24 mm, 0.63 kg/m | 3.02 mm, 0.80 kg/m | - | - |
| NPS 3/8 | 17.1 mm | 2.31 mm, 0.84 kg/m | 3.20 mm, 1.10 kg/m | - | - |
| NPS 1/2 | 21.3 mm | 2.77 mm, 1.27 kg/m | 3.73 mm, 1.62 kg/m | 4.78 mm, 1.95 kg/m | XXS: 7.47 mm, 2.55 kg/m |
| NPS 3/4 | 26.7 mm | 2.87 mm, 1.69 kg/m | 3.91 mm, 2.20 kg/m | 5.56 mm, 2.90 kg/m | XXS: 7.82 mm, 3.64 kg/m |
| NPS 1 | 33.4 mm | 3.38 mm, 2.50 kg/m | 4.55 mm, 3.24 kg/m | 6.35 mm, 4.24 kg/m | XXS: 9.09 mm, 5.45 kg/m |
| NPS 1-1/4 | 42.2 mm | 3.56 mm, 3.39 kg/m | 4.85 mm, 4.47 kg/m | 6.35 mm, 5.61 kg/m | XXS: 9.70 mm, 7.77 kg/m |
| NPS 1-1/2 | 48.3 mm | 3.68 mm, 4.05 kg/m | 5.08 mm, 5.41 kg/m | 7.14 mm, 7.25 kg/m | XXS: 10.15 mm, 9.55 kg/m |
| NPS 2 | 60.3 mm | 3.91 mm, 5.44 kg/m | 5.54 mm, 7.48 kg/m | 8.74 mm, 11.11 kg/m | XXS: 11.07 mm, 13.44 kg/m |
| NPS 2-1/2 | 73.0 mm | 5.16 mm, 8.63 kg/m | 7.01 mm, 11.41 kg/m | 9.53 mm, 14.92 kg/m | XXS: 14.02 mm, 20.39 kg/m |
| NPS 3 | 88.9 mm | 5.49 mm, 11.29 kg/m | 7.62 mm, 15.27 kg/m | 11.13 mm, 21.35 kg/m | XXS: 15.24 mm, 27.68 kg/m |
| NPS 4 | 114.3 mm | 6.02 mm, 16.08 kg/m | 8.56 mm, 22.32 kg/m | 13.49 mm, 33.54 kg/m | XXS: 17.12 mm, 41.03 kg/m |
| NPS 6 | 168.3 mm | 7.11 mm, 28.26 kg/m | 10.97 mm, 42.56 kg/m | 18.26 mm, 67.57 kg/m | XXS: 21.95 mm, 79.22 kg/m |
| NPS 8 | 219.1 mm | 8.18 mm, 42.55 kg/m | 12.70 mm, 64.64 kg/m | 23.01 mm, 111.27 kg/m | XXS: 22.23 mm, 107.93 kg/m |
| NPS 10 | 273.0 mm | 9.27 mm, 60.29 kg/m | 15.09 mm, 95.98 kg/m | 28.58 mm, 172.27 kg/m | XXS: 25.40 mm, 155.10 kg/m |
| NPS 12 | 323.8 mm | 10.31 mm, 79.71 kg/m | 17.48 mm, 132.05 kg/m | 33.32 mm, 238.69 kg/m | XXS: 25.40 mm, 186.92 kg/m |
| NPS 14 | 355.6 mm | 11.13 mm, 94.55 kg/m | 19.05 mm, 158.11 kg/m | 35.71 mm, 281.72 kg/m | - |
| NPS 16 | 406.4 mm | 12.70 mm, 123.31 kg/m | 21.44 mm, 203.54 kg/m | 40.49 mm, 365.38 kg/m | - |
| NPS 18 | 457.0 mm | 14.27 mm, 155.81 kg/m | 23.83 mm, 254.57 kg/m | 45.24 mm, 459.39 kg/m | - |
| NPS 20 | 508.0 mm | 15.09 mm, 183.43 kg/m | 26.19 mm, 311.19 kg/m | 50.01 mm, 564.85 kg/m | - |
| NPS 24 | 610.0 mm | 17.48 mm, 255.43 kg/m | 30.96 mm, 442.11 kg/m | 59.54 mm, 808.27 kg/m | - |
| NPS 30 | 762.0 mm | - | - | - | STD: 9.53 mm, 176.85 kg/m; XS: 12.70 mm, 234.68 kg/m |
| NPS 36 | 914.0 mm | - | - | - | STD: 9.53 mm, 212.57 kg/m; XS: 12.70 mm, 282.29 kg/m |
| NPS 42 | 1067.0 mm | - | - | - | STD: 9.53 mm, 248.53 kg/m; XS: 12.70 mm, 330.21 kg/m |
| NPS 48 | 1219.0 mm | - | - | - | STD: 9.53 mm, 284.25 kg/m; XS: 12.70 mm, 377.81 kg/m |
For NPS 14 and above, SCH 40 is heavier than STD; below NPS 10 the two are the same wall. The same table applies to alloy steel pipe such as ASTM A335, because B36.10M covers both carbon and alloy steel.
Stainless Steel Pipe Schedules (ASME B36.19M)
Stainless pipe uses the S schedules of ASME B36.19M. Light walls (5S and 10S) are common because stainless resists corrosion, so less corrosion allowance is needed [build as an HTML table; check against the current edition of ASME B36.19M].
| NPS | OD (mm) | 5S (Wall / Wt) | 10S (Wall / Wt) | 40S (Wall / Wt) | 80S (Wall / Wt) |
|---|---|---|---|---|---|
| NPS 1/2 | 21.3 mm | 1.65 mm, 0.81 kg/m | 2.11 mm, 1.01 kg/m | 2.77 mm, 1.28 kg/m | 3.73 mm, 1.63 kg/m |
| NPS 3/4 | 26.7 mm | 1.65 mm, 1.03 kg/m | 2.11 mm, 1.29 kg/m | 2.87 mm, 1.70 kg/m | 3.91 mm, 2.22 kg/m |
| NPS 1 | 33.4 mm | 1.65 mm, 1.31 kg/m | 2.77 mm, 2.11 kg/m | 3.38 mm, 2.53 kg/m | 4.55 mm, 3.27 kg/m |
| NPS 1-1/4 | 42.2 mm | 1.65 mm, 1.67 kg/m | 2.77 mm, 2.72 kg/m | 3.56 mm, 3.43 kg/m | 4.85 mm, 4.51 kg/m |
| NPS 1-1/2 | 48.3 mm | 1.65 mm, 1.92 kg/m | 2.77 mm, 3.14 kg/m | 3.68 mm, 4.09 kg/m | 5.08 mm, 5.47 kg/m |
| NPS 2 | 60.3 mm | 1.65 mm, 2.41 kg/m | 2.77 mm, 3.97 kg/m | 3.91 mm, 5.49 kg/m | 5.54 mm, 7.56 kg/m |
| NPS 3 | 88.9 mm | 2.11 mm, 4.56 kg/m | 3.05 mm, 6.52 kg/m | 5.49 mm, 11.41 kg/m | 7.62 mm, 15.43 kg/m |
| NPS 4 | 114.3 mm | 2.11 mm, 5.90 kg/m | 3.05 mm, 8.45 kg/m | 6.02 mm, 16.24 kg/m | 8.56 mm, 22.55 kg/m |
| NPS 6 | 168.3 mm | 2.77 mm, 11.42 kg/m | 3.40 mm, 13.97 kg/m | 7.11 mm, 28.55 kg/m | 10.97 mm, 43.00 kg/m |
| NPS 8 | 219.1 mm | 2.77 mm, 14.93 kg/m | 3.76 mm, 20.17 kg/m | 8.18 mm, 42.98 kg/m | 12.70 mm, 65.30 kg/m |
| NPS 10 | 273.0 mm | 3.40 mm, 22.84 kg/m | 4.19 mm, 28.06 kg/m | 9.27 mm, 60.91 kg/m | 12.70 mm, 82.36 kg/m |
| NPS 12 | 323.8 mm | 3.96 mm, 31.55 kg/m | 4.57 mm, 36.34 kg/m | 9.53 mm, 74.61 kg/m | 12.70 mm, 98.43 kg/m |
Stainless weights here use a density of 7.93 g/cm3, about 1% heavier than carbon steel for the same size. 40S matches SCH 40 up to NPS 10, and 80S matches SCH 80 up to NPS 8; above that the S schedules are lighter, so never swap them without checking this stainless pipe schedule chart.
Pipe Weight Formula (kg/m)
Every figure in this pipe weight chart comes from one weight formula, so you can calculate any size that is not listed.
- Carbon and alloy steel: weight (kg/m) = (OD minus WT) x WT x 0.0246615, with OD and WT in millimetres.
- Stainless steel: use 0.02491 instead of 0.0246615, to allow for its higher density.
- Worked example: NPS 6 SCH 40 has an OD of 168.3 mm and a wall of 7.11 mm. (168.3 minus 7.11) x 7.11 x 0.0246615 = 28.26 kg/m, so a 6 metre length weighs about 170 kg and a 12 metre length about 339 kg.
These are plain-end weights. Bevelled or threaded ends change the figure slightly, and the actual weight can vary within the mill tolerance on wall thickness. For freight and crane planning, add a margin of a few percent to the figures in the pipe schedule and weight chart. If you need the weight of a whole order, send the list with your enquiry and we include it on the quote.
Schedule 40 or Schedule 80: Which Do You Need?
This is the question buyers ask most when they look at a pipe schedule chart, and the answer comes from pressure, corrosion and the project specification, not from habit.
- Pressure and temperature: the required wall is calculated from the design pressure, temperature and the allowable stress of the material under the piping code your project uses, usually ASME B31.3 for process piping. The calculation gives a minimum wall; the schedule chosen must meet it after mill tolerance and corrosion allowance are deducted.
- Corrosion allowance: carbon steel lines often add 1.5 to 3 mm for corrosion, which can push a line from SCH 40 to SCH 80.
- Threaded and small-bore lines: threading removes metal, so small threaded lines are often SCH 80 even at low pressure.
- Mechanical strength: small branches, vents and drains often use SCH 80 or SCH 160 for strength against vibration and knocks, not for pressure.
- Weight and cost: the pipe weight chart shows SCH 80 is roughly 30 to 50% heavier than SCH 40 in the common sizes, so over-specifying adds cost, weight and welding time.
Specifications usually settle the choice in a piping class sheet. If yours does not, your piping engineer should calculate the wall; we can confirm what is in stock for each option, but we do not replace a design calculation.
STD, XS and XXS Explained
Older drawings and many piping specifications use weight classes instead of schedule numbers. STD (standard weight) equals SCH 40 up to NPS 10, then stays at 9.53 mm from NPS 12 upward. XS (extra strong) equals SCH 80 up to NPS 8, then stays at 12.70 mm from NPS 12 upward. XXS (double extra strong) has no schedule equivalent and is used for very high pressure in small sizes. When a drawing says STD or XS for a large pipe, use the weight class, not the schedule, because they differ above NPS 10 in this pipe schedule chart.
Tolerances and Checking Pipe on Site
The wall thickness in a pipe schedule chart is nominal. Most ASTM pipe standards allow the wall to be up to 12.5% under nominal at any point, which is why design calculations deduct mill tolerance. OD tolerances are tighter and depend on the standard and size. When pipe arrives, check that the size, schedule, grade and heat code stencilled on each length match the order and the EN 10204 certificate, measure the wall with an ultrasonic gauge at a few points on critical lines, and record the results before the pipe is cut. Keep a copy of this pipe weight chart with the inspection records so the nominal values are always to hand.
Common Mistakes When Using a Pipe Schedule Chart
Most sizing errors on site come from a handful of avoidable mistakes.
- Treating NPS as the outside diameter: an NPS 2 pipe is 60.3 mm OD, so ordering "50 mm pipe" without saying NPS or DN causes confusion. Always quote NPS or DN, and give the OD in millimetres if there is any doubt.
- Mixing up SCH 40 and STD above NPS 10: on NPS 14, SCH 40 is 11.13 mm but STD is 9.53 mm, a difference of over 15% in weight.
- Using carbon steel walls for stainless: 40S and 80S are lighter than SCH 40 and SCH 80 in the larger sizes.
- Forgetting fittings: butt-weld fittings must match the pipe wall, so an elbow ordered in the wrong schedule will not line up at the bevel.
- Ignoring tolerance: the minimum wall can be 12.5% below the figure in the pipe schedule chart, which matters on high-pressure lines.
A quick check against the pipe weight chart and the drawing before ordering avoids most of these problems.
Related Pages
For grades and stocked sizes see our Pipes page; for butt-weld fitting walls matched to these schedules see Pipe Fittings; for general buying questions see the Piping FAQ. If you need a printable copy of this pipe schedule and weight chart, ask our team and we will send a PDF version [confirm].
Pipe Schedule Chart FAQs
What does schedule mean on a pipe?
It is a number that sets the wall thickness for each nominal size, so the same schedule has different wall thicknesses in different sizes, as the pipe weight chart above shows.
Is SCH 40 the same thickness in every size?
No. SCH 40 is 2.77 mm on NPS 1/2 but 9.27 mm on NPS 10, as this pipe schedule chart shows.
What is the difference between NPS and DN?
NPS is the North American nominal size in inches; DN is the metric equivalent. DN 50 equals NPS 2, and DN 200 equals NPS 8.
Can I use the carbon steel chart for stainless pipe?
Only where the S schedule matches the carbon steel schedule; use the stainless table for 5S, 10S and for 40S and 80S above NPS 10 and NPS 8.
Does the chart apply to API 5L line pipe?
Yes. API 5L uses the same outside diameters and many of the same walls as ASME B36.10M, although line pipe is often ordered by wall thickness in millimetres rather than by schedule.
Where do DN sizes come from?
DN sizes come from ISO and EN practice. They name the same pipes as NPS, so DN 100 and NPS 4 share a 114.3 mm outside diameter.
How do I work out the inside diameter?
Subtract twice the wall thickness from the outside diameter given in the pipe schedule and weight chart.
How accurate are the weights?
They are theoretical plain-end weights from the standard formula; actual weights vary within mill tolerance.
Get a Quote for These Sizes
Found the size you need in the pipe schedule and weight chart? Send your list with NPS, schedule, grade and quantity, and we will confirm stock, weight and price within [confirm] working hours. Call +971 6 533 8167, WhatsApp [confirm number] or email sales@leemaeng.com.
Reviewed by [Engineer name], [Role], Leema Engineering Works. Last reviewed [date].